Quality Italian Components
Handbook 2.1

Adjustable product control contact lever unit inductive proximity sensor version

KP

Adjustable product control contact lever unit inductive proximity sensor version

Use: this kit was created as an accessory for the format changeover positioners. It allows adjusting the height of the control contact lever unit in order to detect the product flow.

It is suitable for applications where you need to control the single product track, without interrupting the entire flow of the remaining tracks.

State of supply

The kit is supplied without sensors and cables, but they can be supplied on request.

Kit complete with 1 drive jack with reduction gear body in RAL9005 black reinforced polyamide, 1 Rack, 1 worm screw, 1 knob fastened with a UNI5739 M6x12 hex head screw and washer for M6 screw, 1 screw cap in RAL3020 red polyamide, 1 gearwheel in reinforced metal, 1 brake with tightening wing nut in RAL3020 red reinforced polyamide (wing nut cap in black RAL9005); 1 idler jack with reduction gearbox in RAL9005 black reinforced polyamide; 1 rack, 1 gearwheel in reinforced metal, 2 bracketing plates in AISI 304 stainless steel, 1 hexagonal synchronization and transmission shaft 16, 1 M20 control contact lever bar, 1 20Ø sensor holder bracket fastening shaft, 1 aluminium cable duct, technopolymer cable duct with 18Ø hole for cable passage, control contact levers (max. 10) in RAL9005 black reinforced polyamide with fastening knob, sensor holder in AISI 304 stainless steel ,pins for sensor, 8 UNI5739 M6x55 hex head screws, 8 UNI7474 self-locking nuts, 16 M6 screw washers, 2 UNI5739 M8x20 hex head screws, 2 M8 screw washers.

Material version Dry environment Z

Racks, hexagonal shaft, M20 control contact lever bar and nuts and bolts in galvanised steel, worm screw in phosphated steel, pins for sensor in galvanised free-cutting leaded steel.

Material version Wet environment B

Racks, worm screw and pins for sensors in steel with chemical nickel-plating (thickness 10÷15 µm), hexagonal shaft and M20 control contact lever bar in AISI304 stainless steel, and stainless steel nuts and bolts. WET

Characteristics: the synchronised movement of the two jacks occurs by means of the hexagonal synchronisation and transmission shaft. Permanent setting is assured by a brake that prevents any loss of position caused by external factors (e.g. vibrations).

Warning:

In order to protect the internal transmission devices, if you use the knob for movement, the brake will not fully lock the position.

Maintenance: not required.

Standard pack: 1 piece.

Kit's vertical travel: 400mm.

Nominal torque transmissible 12 Nm (4.5 Nm version on request).

Rack's travel per turn: 1 knob turn = 8 mm of rack travel.

Reduction ratio i=16 (16 knob turns -worm screw- are equivalent to 1 turn of the worm gear with hexagonal seat).

Combinations

Product Gallery

QUANTITY DISCOUNT

Qty 1+ 2+ 4+ 8+
Discounts - -5% -10% contact us
Code order Version environment Distance between centres rack side drive Jack version Material nuts and bolts Rack finish Weight Kg Stock piece Buy Draw
KPR06A0500RZF dry 500 mm R F galvanised galvanised 7.7 558,44
KPR06A1000RZF dry 1000 mm R F galvanised galvanised 9.9 561,62
KPR06A1500RZF dry 1500mm R F galvanised galvanised 12.1 564,80
KPR06A2000RZF dry 2000mm R F galvanised galvanised 14.3 567,99
Customisations Versions with reduction gear body in different colours, and with customisable logo are available on request (min. 300 pieces, price and delivery on request), rack lengths other than standard ones are available on request

 Products not in stock minimum order: 1 piece, delivery in 10 days for the dry environment version, delivery in 15 days for the wet environment version